Quadro Quadro16xi Guía de instalación Pagina 83
- Pagina / 150
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Quadro Manual II: Administrator's Guide Administrator’s Menus
Quadro2x, 2xi, Quadro4x, 4xi, Quadro16x, 16xi; (SW Version 5.2.x) 82
Please Note: The Plug and Play service is only available for the supported SIP phones (see the list below). This service will not work in case the SIP
phone is already manually configured or if it is not reset after enabling the Enable PnP to IP lines checkbox.
Enable Firmware Version Control checkbox is used to control the firmware version running on the SIP Phone attached to the Quadro. This service
also allows you to have the new firmware automatically downloaded and installed on your SIP Phone (in case your SIP phone was running an old
firmware upon connecting to the Quadro or when the Quadro’s firmware has been updated and the compatibility was changed to the higher firmware
version of the SIP phone). Every new firmware of Quadro is compatible to a certain firmware version of each supported SIP phone. If you are running
older firmware on your SIP phone, this service will automatically download and install the newer firmware on your SIP phone.
Please Note: The Firmware Version Control service is only available for the supported SIP phones (see the list below).
Attention: Do not select this checkbox if you wish to run other firmware version on your SIP phone than the one compatible with the Quadro.
The Configure IP phones from drop down list is used to select the Quadro's interface where the IP phones are connected (LAN or WAN).
The alternating Hide disabled IP lines and Show disabled IP lines buttons are used to respectively hide or show the IP lines that have not been
activated with a feature key. To enable the lines, install a feature key from the
Features page.
The Manage IP Phones Templates link takes to the IP Phones Templates
page where custom IP phone templates may be created.
The Upload IP Phones Logo link takes to the IP Phones Logo
page where custom logo for the IP phone may be uploaded.
The
FXS
Gateway Management link takes to the page where Quadro FXS gateway devices may be defined in order to add additional FXS lines to the
phone type and the configuration details.
olumn
, the
y the SIP phones.
IP phone model
Other
the well protected strong
IP Phone to obtain the
ed on the phone. Refer to the user’s manual
Quadro IP PBX.
The IP Lines table lists all available IP lines with additional information
about each of them: number of the extension attached to it, information
about the
Each column heading in the tables is link. By clicking on the column
heading, the table will be sorted by the selected column. When sorting
(ascending or descending), arrows will be displayed next to the column
heading.
By pressing on the IP line # link in the Available IP Lines c
Edit IP Line page specific for the current IP line is opened. This page
offers a group of manipulation radio buttons that allows you to enable
the IP line and to configure it to for use b
Inactive – this selection disables the corresponding IP line.
SIP Phone – this selection configures the IP line for a SIP phone to be
connected to the Quadro’s LAN.
• Phone Model drop down list is used to select the
to be used by the receptionist. The drop down list, excluding Other
selection, enables the MAC address text fields used to insert the
MAC Address of the corresponding SIP phone. Use
selection if your SIP phone is not in this list.
• Line Appearance text field requires a number of simultaneous
calls supported by the SIP phone.
• Username and Password are required for this selection. They
should match on both the Quadro and the SIP phone for a
successful connection. The Password field is checked against its
strength and you may see how strong is your inserted password is
right below that field. To achieve
password minimum 8 characters of letters in upper and lower case,
symbols and numbers should be used. If you are unable to define a
strong password, press Choose Generated Password to use one
of system defined strong passwords
• Transport drop down list is used to select the SIP protocol
transport layer - UDP, TCP or TLS. For TLS you may activate the
TLS certificate update mechanism from
latest certificate generated by the Quadro.
For automatic SIP phone configuration, the SIP phone should be
reset/rebooted. The appropriate configuration will then be automatically
downloaded from Quadro to the SIP Phone.
Please Note: For automatic configuration, some SIP phones may
require additional actions to follow the restart. For example, by default
the IP Dialog SIP Tone II is in a non-auto-provisioning mode, so it
should be manually enabl
Fig. II-143: IP Line Settings page
- Edition 1, June 2011 1
- Table of Contents 2
- Quadro’s Graphical Interface 6
- Recurrent Buttons 7
- Recurrent Functional Buttons 7
- Administrator’s Menus 8
- System Security Management 12
- • User Rights Management 13
- • IP Line Settings 13
- • Firewall/NAT 13
- Network Status 15
- Memory Status 19
- Hardware Status 20
- SIP Registration Status 20
- IP Lines Registration Status 20
- License Status 21
- IP Routing Configuration 21
- Configuration Management 23
- Time/Date Settings 28
- Mail Settings 29
- SMS Settings 30
- Firmware Update 30
- Automatic Firmware Update 32
- Networking Tools 33
- SNMP Settings 34
- Diagnostics 35
- System Logs 35
- Fig. II-64: Features page 37
- Upload Language Pack 38
- User Rights Management 39
- Users Menu 41
- Extensions Management 41
- User Extension Settings 43
- Call Park Extension Settings 49
- Attendant Extension Settings 55
- • PSTN – calls to PSTN 56
- • User Input 58
- • No input 58
- • Signs (“*” and “#”) 58
- Add Multiple Extensions 61
- Extension Codecs 62
- Call Park Service 63
- Recording Box 64
- Receptionist Management 65
- * key combination (see 67
- Authorized Phones Database 69
- Call Back Services 70
- Telephony Menu 72
- Call Statistics 72
- RTP Statistics 75
- FAX Statistics 76
- SIP Settings 76
- Host aliases for SIP 77
- RTP Settings 77
- NAT Traversal Settings 78
- Line Settings 81
- Onboard Line Settings 81
- IP Line Settings 82
- Supporte 84
- IP Phones Templates 85
- Phones Logo 86
- FXS Gateway Management 87
- Loopback Settings 88
- Hot Desking 88
- FXO Settings 89
- Gain Control 95
- SIP Tunnel Settings 95
- • Failover Rea 100
- Local AAA Table 103
- Global Speed Dial Directory 104
- Allowed C 104
- Best Matching Algorithm 106
- VoIP Carrier Wizard 108
- RADIUS Client Settings 109
- Voice Mail Common Settings 111
- Dial Plan Settings 112
- 3PCC Settings 112
- RTP Streaming Channels 113
- Call Recording Settings 113
- Advanced PPP Settings 117
- VPN Configuration 117
- Dynamic DNS Settings 124
- Firewall and NAT 125
- Advanced Firewall Settings 125
- IP Pool 128
- IDS Log 130
- Network Menu 131
- DNS Settings 131
- DNS Server Settings 131
- Registration Form 134
- Voice Mail Profiles 135
- Administrator’s Logout 139
- Welcome 140
- Administrator Settings 141
- Extension Settings 147
- EPYGI TECHNOLOGIES, LTD 149
- Software License Agreement 149
Relacionado con productos y manuales para Sistemas premisa branch exchange (pbx) Quadro Quadro16xi
(2 paginas)
(11 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales